ppti.info Personal Growth Astm A860 Pdf

ASTM A860 PDF

Friday, September 20, 2019


This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A_机械/仪表_工程科技_专业资料。Designation: A/AM – 10 Standard Speci?cation for Wrought High-Strength Ferritic Steel.


Astm A860 Pdf

Author:DELILAH DISHMON
Language:English, Spanish, Dutch
Country:Poland
Genre:Religion
Pages:759
Published (Last):05.06.2015
ISBN:556-4-73286-269-8
ePub File Size:22.67 MB
PDF File Size:19.43 MB
Distribution:Free* [*Regsitration Required]
Downloads:46515
Uploaded by: JILLIAN

ASTM A - Download as PDF File .pdf), Text File .txt) or read online. A / AM Standard Specification for Wrought High-Strength Ferritic Steel Butt-Welding Standard + Redline PDF Bundle, 10, $, ADD TO CART. Download astm a am standard specification for wrought high strength ferritic steel butt welding fittings ppti.info ( KB) now. Fast and easy at.

A number in parentheses indicates the year of last reapproval. A superscript epsilon?

One or more of the supplementary requirements may be speci? Within the text, the SI units are shown in brackets.

Popular Publishers

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Unless the order speci? Referenced Documents 2.

Description

Current edition approved Nov. Published December Originally approved in DOI: Ordering Information 3. General Requirements 4. Failure to comply with the general requirements of Speci? In case of con? Materials and Manufacture 5. Box , Arlingate Ln. The chemical composition shall conform to Table 1. This does not preclude the use of deoxidizers. This examination shall be performed in accordance with a written procedure and shall be performed after? Only the side wall area of the tees need be examined.

This area is de? Internal and external surfaces shall be examined when size permits accessibility. No cracks shall be permitted. Other imperfections shall be treated in accordance with After the removal of any cracks, the tees shall be re-examined by the original method.

Acceptable tees shall be marked with the symbol PT or MT, as applicable, to indicate compliance. NDE personnel shall be quali? Heat Treatment 6. Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment.

Fittings shall subsequently be heat treated by normalizing, quenching, and tempering or stress relieving in accordance with Speci?

Chemical Composition 7. The results shall conform to Table 1 for either heat or Speci?

You might also like: ASTM C289 PDF

The chemical composition thus determined shall conform to Table 1. The product analysis shall be the basis for rejection. A chemical analysis shall be performed on deposited weld metal for each heat of? The weld metal shall be deposited in accordance with the quali?

The nickel content of the deposited weld metal shall not exceed 1.

Notch Toughness Properties 8. The testing shall be performed as speci?

A chemical analysis shall be performed on deposited weld metal for each heat of? The weld metal shall be deposited in accordance with the quali? The nickel content of the deposited weld metal shall not exceed 1. Notch Toughness Properties 8. The testing shall be performed as speci?

Full size Charpy, V-notch specimens shall be used whenever possible. Small size specimens shall be used only when the material thickness does not permit full size specimens.

The impact specimens shall not be? All base metal specimens shall be removed with the axis of the specimens longitudinal to the direction of primary metal? Weld-metal specimens shall be specimens with the axis transverse to the weld seam. Tensile Requirements 9. Only the ultimate tensile strength need meet the minimum requirement of Table 2. Hardness Requirements Dimensions Rectangular specimen for thickness less than 5?

Width of specimen 11? Cvenergy absorptionC; measured at? Size, mm 10 7. For each 1? When the section thickness lies between two values de? C These requirements are intended to minimize fracture initiation.

Also read: ASTM E45 PDF

The requirements are not intended to give assurance against fracture propagation. Workmanship, Finish and Appearance The wall thickness at all points shall be at least ?

Repair by Welding Base Metal Electrodes for the shielded metal-arc process shall be of the low-hydrogen type. Hydrostatic Test Transverse-weld tensile strength shall be reported in ksi.

Popular Publishers

Product Marking In addition, quench and tempered? NOTE 1—For purposes of identi? Rejection and Rehearing Rejection shall be reported to the producer or supplier promptly in writing. In case of dissatisfaction with the results of the tests, the producer or supplier may make claim for a rehearing.

ASTM A860 PDF

In addition, if requested to provide test reports, the manufacturer shall also provide the following, when applicable: The purchaser may specify in the order a speci? The bar coding system, if applied at the discretion of the supplier, should be consistent with one of the published industry standards for bar coding.

If used on small? Keywords Committee A01 has identi? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.The weld metal shall be deposited in accordance with the quali?

Other imperfections shall be treated in accordance with Section Section IX. Three column 1. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The nickel content of the deposited weld metal shall not exceed 1.

First Grade Free 1st grade reading comprehension Passages - 36 weeks, printable PDF worksheets to use in the classroom or at home.

VERNIE from North Carolina
Please check my other posts. I enjoy music. I do enjoy studying docunments delightfully.